Ditch The Boring Case - How To Put On Cell Phone Charms On Any Device

Overview

How To Put On Cell Phone Charms - Different Ways

Securing Phone Charms Onto A Phone Case With An Opening

• Remove your phone from its case. Dealing with an empty phone case enables you to properly affix the charm and guarantees that your phone remains unharmed during the process. Therefore, take your phone out and place it aside.
• Find the opening for the mute button on the phone case. If your phone case lacks a mute button opening, don't worry! Check for other available openings in the case where you could attach a charm, such as the audio jack or charging port.
• Insert the looped section of the phone charm into the mute button opening. Draw the looped string at the charm's end through the mute button hole until it emerges on the opposite side. Ensure that the beads or charm itself do not pass through the opening.
• Create a knot using the loop of the phone charm. Use the hand holding the case to open the string loop of the charm. Gather the charm or beads with your other hand and thread them through the loop. This will form a basic knot, securely attaching your phone charm or strap to the case.
• Insert the phone back into the case. That's all there is to it! Your phone should smoothly fit into the case.

Adapting A Phone Case Lacking An Opening

• Choose the desired location for the phone charm. Take your phone out of the case and use a fine-tip permanent marker to mark on the case where you want the charm to be.
• Create two holes in a soft or hard plastic case using a needle. Heat the pointed end of a sewing needle with an open flame. Hold the needle over the flame briefly, then promptly press it onto the marked spot on the case.
• Apply gentle pressure to make the initial hole and repeat the process for the second hole. The number of attempts required may vary depending on the case's thickness.
• Position the two holes approximately one centimeter apart, ensuring they are close but not touching.
• Utilize a 5/64 drill bit to bore a hole in a plastic case. Place a piece of cardboard on the inner back surface of the phone case. Align the drill with the mark you made earlier and drill at a 45-degree angle.
• This technique carries more risk, especially if your hand isn't steady, as the drill may scratch the case. However, it is recognized to be effective on more robust cases, such as those manufactured by OtterBox.
• Thread the string of the phone charm through the hole(s) you made. Pass the loop of the phone charm through the hole. If the loop is too large, no problem! Connect the loop to a string and needle, then pull the needle through the hole.
• Fasten the phone charm to the case using a basic knot. Thread the charms or beads through the loop, and there you have it! You've successfully affixed a phone charm to a case without a hole.

Connecting Phone Charms To The Audio Jack Of The Phone

• Identify the audio jack on your phone, which is the port where you insert your headphones. It's important to note that newer phones may not have audio jacks, so this approach is more suitable for older models or Android devices.
• Insert a pre-made phone jack charm. Numerous ready-made audio jack charms are available in the market. Just insert the base of the charm into the audio jack.
• Insert a phone jack charm holder. If you wish to affix a dangling charm or bracelet to your phone, use an audio jack plug equipped with a lobster claw or ring. This allows for the seamless connection of any charm, and all you need to do is fasten the charm to the end of the plug.

Removing The Charm

• Loosen the knot around the phone case opening.
• Thread the charm back through the string loop.
• Pull the string out of the phone case opening.

Creating Phone Charms

• Decide on the length you want for your phone charm.
• Utilize a ruler to measure the desired length, determining how long your bead pattern needs to be. If you're creating a phone charm strap, employ a cloth measuring tape to measure around your wrist.
• Arrange your beads and charms in a line. Create a pattern of your preferred length to get a visual representation of the final product.
• String a stretchy cord or elastic thread through the beads. Begin with the bead at the top of your pattern, as it will be the uppermost part of your charm. Follow the sequence of your pattern until all the beads are threaded onto the cord.
• Opt for a transparent string to highlight the color of your beads, or choose a colored cord for an extra playful touch.
• Fold and tie the ends of the beaded string together to form a phone charm strap. Cut the string from the roll, leaving approximately 4 to 6 inches (10 to 15 cm) of excess string, and secure the beads with a double knot.
• With the leftover string, tie another double knot to fashion a smaller loop of about 1 inch (2.5 cm) in length.
• Reinsert the string through the beads to create a single-stranded charm. Pass the end of the string through the last bead you threaded, repeating this process until you reach the top of the pattern.
• Once completed, cut the string from the roll, and you'll have two string ends protruding from the top bead. Leave approximately 2 inches (5.1 cm) of excess string.
• Attach a jump ring and lariat to the single-stranded phone charm. Ensure the beads are firmly in place by tying a surgeon's knot. Trim away the excess string from the knot, and thread an open jump ring through it. Connect the lariat to the jump ring, and use pliers to secure the jump ring.
• Connect the phone charm to your phone case. Well done! You've crafted your own stylish and on-trend phone charm.

Frequently Asked Questions - How To Put On Cell Phone Charms

Could Cell Phone Charms Harm My Phone?

What Is The Mechanism Behind Light-up Phone Charms?

Who Initiated The Trend Of Phone Charms?

Conclusion